Tomahawk tz 9010 instructions for use. User manual
A modern security system should include a large number of functions that provide comprehensive control over the state of the car.
The issue of protecting a vehicle from theft is a topical issue for every car owner.
Car alarms are one option for those who care about protection. The Tomahawk 9010 brand has become one of the most sought after in the modern market.
What are the characteristics of the models?
- There is an additional feedback function with the car owner. It is usually supplied with all modern models.
- Protection against signal interception is constantly enhanced.
- The alarm allows you to start, warm up the engine remotely.
The instruction for 9010 is needed to get acquainted with all the properties that this or that device has, and the buyer had the following information:
What are the most common faults?
Many motorists are faced with a situation where the 9010 key fob does not respond to any movements. Such situations develop for several reasons.
It is recommended to contact the installers if the fuel pump does not turn on when the alarm 9010 is working. They will check the quality of the signal, the connections are already in place. The central locking drive requires additional checks if the doors do not close, do not respond to buttons.
The battery is checked in the case when the key fob started to fail. If it doesn't help, you need to reprogram.
Finally, the faults are clearly related to the communication module loop when the alarm flashes 10 times.
Features of setting alarms Tomahawk
To set up the Tomahawk 9010, it is usually enough to press a combination of buttons on the key fob, or one of them. Here it is important to follow the instructions issued by the manufacturer. In order for the system to work correctly, it is necessary to adjust the sensors that are responsible for the timely response to extraneous interference.
Sometimes alarms do not work due to the fact that the sensors are not fixed at the proper level of quality. This is also due to low sensitivity. The work connected with increase in sensitivity consists of several stages.
As for the process of resetting the software on the alarm, it is performed as follows. The ignition must be turned off. Then nine times press the button on which there is an inscription Override. The next step is to turn on the ignition. And again we press the same button, but only once.
The next button we need is the one with the padlock. Finally, the ignition is completely turned off. The parking lights will flash five times if done correctly.
It is possible to reset the settings to the original parameters associated with the function remote start. For this, the same procedures are followed. But the Override button is pressed not nine times, but ten times. The parking lights flash six times. This means the reset is complete.
A separate procedure exists to enable the auto-start function in the 9010. The shift lever is moved to the neutral position. Then they move on to tightening the "handbrake". And press the button with the appropriate appointment on the key fob. The key is pulled out of the ignition lock as soon as a characteristic signal is heard. For the next thirty seconds, you need to close the doors, leave the salon.
What are the advantages of the device?
It is worth paying attention to the functions that the car alarm performs before making the final choice. This will help you understand what features you will encounter during operation.
The Tomahawk series system has the following set of advantages that also become functions.
- There is a built-in clock with a timer, an alarm clock.
- A special mode of operation is available to the driver, which implies significant energy savings. In this situation, the car alarm does not work at full capacity.
- Automatic protection of doors and trunks with a hood.
- Even when the engine is on, the system runs a self-diagnosis of the machine. It will quickly point out faults if any.
- The Tomahawk system will help you control the temperature inside the cabin with maximum accuracy. After all, there is an additional sensor inside. You just need to specify the temperature range.
- Tomahawk is an alarm that is compatible with cars of almost any brand. Even the installed gearbox on the transport device does not matter. It doesn't matter what engine the car is running on.
- The remote control is suitable for automatic shutdown, engine start.
- The same remote is used to disable the siren itself. It is easy to attach to a bunch of keys, which is facilitated by its miniature size.
- The performance of functions is confirmed not only visually, but also by voice messages.
- Work continues around the clock.
Installation is easy, even if the person has no experience with similar work. Malfunctions occur only after a while. 
The main thing that is required is the installation of an electronic unit. It is through him that the device is controlled, and he is in the cabin. It is recommended to set the antenna going to the system unit as high as possible. Then all signals from the remote control will be received without interruption.
Contacts for antenna 9010 with electrical wiring, metal objects are not allowed. Otherwise, the efficiency of the structure is reduced. As for the siren itself, then the best place for its installation - the engine compartment. Then outsiders will have minimal access to the part. Only autonomous varieties are installed in the service key well. Installation is carried out only with the horn down.
In such conditions, moisture will definitely not get inside. The main thing is to properly organize the connection of wires inside the cabin in order to prevent excessive oxidation.
The dashboard is assembled only after the owner has completed the complete setup of the 9010. An important step is the soldering of the wires at the moment when the central lock is connected. The connection points are attached to each other using ordinary electrical tape, it copes well with its functions.
It is enough to find the right connectors, following the manufacturer's instructions. The instructions provide detailed color schemes for electrical equipment, but if necessary, the information is easy to find on the Internet. As well as ways to restore the factory settings.
The shock sensor is securely fixed with ties and adhesive tape, it also increases the functionality of the system. The same goes for LED indicators. Their place is where the front pillar and center panel are located.
Your engine can die at any moment
- Do you think nothing can happen to the engine on a small run?
- If the car began to "eat" oil, then the engine had only a few kilometers left to live.
- 98th gasoline will not save you from an early repair!
The product line of Tomahawk alarms is constantly updated. Not surprisingly, many models were discontinued and replaced by new devices with enhanced functionality and increased reliability.
The alarm market in Russia is developing rapidly. It was once thought that an alarm should cost at least five percent of the price of a car. Now the first-class Tomahawk 9030 system can be purchased for nine thousand rubles.
The fact is that technological progress does not stand still. Every year, new technologies appear that make old alarms look like a rarity. And it's not even that the new boards are more productive, and the key fob has a dozen additional functions. It's just that thieves are also improving, constantly coming up with new ways of hacking.
No wonder Tomahawk is doing everything possible to bring quality alarms to the market at an affordable price with new protective systems. Not only that, other brands do the same. Great competition and constantly growing demands have turned modern anti-theft systems into real works of art.
Description of alarms
Alarms "Tomahawk" have auto start and feedback (top models). They work with interactive and dynamic codes. As a result, the frequency range is 434 and 868 megahertz.
Tomahawk 9.9
Honestly, modern systems have such an impressive list of features that it can take several hours to parse them. Take, for example, the top model Tomahawk 9.9. Here is the complete feature set of the anti-theft device:
- Feedback;
- vehicle search system in case of theft;
- setting the engine start depending on the temperature;
- bypassing the faulty zone;
- four key fobs and additional control channels;
- remote status polling;
- autorun;
- automatic arming;
- two-level shock sensor;
- "Comfort" system;
- engine blocking;
- control central lock;
- built-in memory;
- security mode;
- engine activation at a certain temperature;
- the possibility of programming locks;
- data on the state of the sensors;
- several modes of operation;
- remote trunk opening;
- immobilizer;
- turbo timer.
As you can see, there are more than enough functions. Some of them need to be told a little more. The most popular of all is autorun. In addition, it allows you to activate a number of other functional additions.
Autostart allows you to activate the engine at a great distance from the car. For example, in winter, before driving, you activate this Tomahawk alarm function at home, and the engine starts to work, warming up the interior.
Advice! In the summer heat, the auto-start function can be used to activate the air conditioner and get into a cool interior.
Alarm "Tomahawk" 9.9 is programmable. This means that you can configure the autorun function yourself. For example, it will be activated when a certain temperature is reached.
Important! In order for temperature detection to become a reality, a special sensor is installed under the hood.
Special attention deserves the alarm function "Tomahawk" 9.9 - feedback. Keychain and board block controls are constantly communicating with each other. Once the process is interrupted, the system will notify you with a corresponding sound signal.
I would also like to recall another possibility that the Tomahawk 9.9 alarm has, namely, remote opening and closing of locks. One press of the button on the key fob is enough to open the trunk. This is a great time saver.
Other Tomahawk alarms and their characteristics
The company "Tomahawk" produces a variety of alarms for a variety of target audiences. In its assortment, you can find anti-theft systems designed for cars of the Laxuary class and for ordinary “nines” or “sevens”. However, all devices have some common features, such as:
- five-button keychain with a high-quality screen;
- Feedback;
- remote heating and engine start;
- enhanced signal interception protection.
All top-end Tomahawk alarms have these features. Perhaps now on sale and you can find models without feedback, but in 90 percent of cases they have long been discontinued.
It's nice to see that the Tomahawk company tries to make each alarm unique. This is expressed in the set of capabilities that a particular model has. As a result, the car owner can make a selection for himself and save money.
Important! Some drivers do not need additional features at all, most just need autostart in order for the car to work smoothly in the winter.
Take, for example, the Tomahawk TZ-9010 alarm. She possesses:
- anti-scanner,
- autorun,
- anti-grabber,
- protection against false positives.
If necessary, this device can call the driver if something goes wrong with the machine. A nice addition to the main characteristics is self-diagnosis. In the event of a breakdown, the Tomahawk 9.9 alarm will notify the driver of the malfunction.
Alarm "Tomahawk" TZ-9020 in addition to the above functionality is equipped with non-volatile memory. This means that the system will remember absolutely everything, even if the power is turned off. Other nice additions include a two-level power sensor and an immobilizer.
Alarm "Tomahawk" TZ-9030 has an extended range, it is 1200 meters. The Z3 has a remote trunk release function and can lock the engine if it is started without permission.
Important! Alarm "Tomahawk" Z3 can be installed both on cars with automatic transmission and with manual transmission.
The Tomahawk TW-7000 has been out of production for a long time. But it still stands on millions of cars. Therefore, it is simply impossible not to say a few words about her. It gained immense popularity among motorists because it had such features as:
- auto detection,
- protection against false positives;
- defense against attack.
The system was able to automatically switch to security mode and was extremely convenient to use. There were legends about her invulnerability.
User manual
First, an important clarification needs to be made. All Tomahawk alarms have similar operating instructions. But in some manuals for systems with advanced functionality, there is simply detailed description every function.
You need to start by adjusting the sensitivity of the sensors. This is extremely milestone. If you set the device incorrectly, even a breath of breeze will cause a siren to howl. To configure, you need to perform the following steps:
- Put the system into reprogramming mode.
- Select a value from 1 to 10 on the sensitivity scale.
- Increase the sensitivity gradually until you reach the desired value.
In some cases, during the operation of the alarm, drivers enter too many settings, due to which the entire system starts to work incorrectly. In this case, you just need to bring down the old settings.
This can be easily done with the OVERRIDE button. Click on it nine times with the ignition off. Turn the key and push the button. There will be another one sound signal. After that, it remains to attach a finger to the image of the lock.
At the end of this procedure, you need to turn off the ignition. If everything was done correctly, the parking lights will flash five times, and the Tomahawk alarm will reset. All settings will return to their original settings.
In order for the operation of the Tomahawk alarm to be as convenient as possible, it is impossible not to recall such a function as autorun. To activate it, the car must first be parked. Then you need to switch to neutral and pull the handbrake all the way. Now you can press the button with the corresponding designation. An audible alert will sound at the end.
Important! After you hear the sound, remove the key from the lock and leave the salon within half a minute, remembering to close the door at the same time.
To turn on the sound on the Tomahawk alarm, there is a special button on the key fob. Moreover, the liquid crystal display shows whether the soundtrack is on or off. This can be easily understood by the speaker icon.
Programming basic functions is done via the OVERRIDE button. Usually it is located under the steering wheel, provided that the alarm was installed in the auto center. If you did everything with your own hands, then finding the right key for you will not be difficult.
Results
The company "Tomahawk" provides a wide range of alarms for every taste and budget. Refusal of unnecessary functions for you allows you to purchase a system with autorun for 7-8 thousand rubles, which is more than a good deal.
Separately, it is necessary to mention the ease of use. Even complex programming actions can be carried out with a single button. It is enough to know the click algorithm and all settings will be reset.
The new sets of security systems contain operating instructions. "Tomahawk 9010" is no exception. A detailed study of the manual makes it possible to use the system as efficiently as possible, taking into account the available features. The alarm in question is a modern car security kit that will satisfy the most picky motorists with its functionality. It should be emphasized that together with high functionality the presented modification has an acceptable cost. When choosing one or another series, you need to take into account and understand the design differences and optional support.
General Description and Usage Guide
Different modifications of the signaling kit have similar operating instructions. "Tomahawk 9010" has the following important options:
- Scan protection, feedback, anti-grabber.
- blocking power unit and turn off the signal in emergency mode.
- Individual password, response from memory.
- Temperature sensor, backlight, immobilizer.
- Built-in time, alarm clock, countdown timer, central lock.
- Disabling the security mode in sequential order, the option to search for a car.
- Auto heating "Tomahawk 9010" allows you to warm up the engine without opening the car doors.
The security system is controlled using a key fob in the form of a remote control with a liquid crystal screen. Information on the display comes through sound feed, symbolic messages and in vibration mode.
Important Notations
In the Tomahawk 9010 security system, these include:
- Activation of the security mode. It is carried out by a button, which shows a small lock and a speaker.
- Shutdown. Produced by pressing the image with a crossed-out gramophone and a lock.
- A schematic copy of a vehicle with various symbols (doors, trunk, hood) is oriented to indicate the corresponding element.
- The central lock is adjusted by acting on a button with a similar display.
- It is also important to use the "Jack" key (search for a car) and the impact symbol (indicates the magnitude and location of the mechanical impact).
Distinctive parameters
Car alarm "Tomahawk 9010" has options similar to similar modifications. Only key rings differ - they have a different shape, but they can interact with each other. Remotes of various series are double-sided, have a response range of about one and a half kilometers, and are equipped with identical functions.
Regarding the digital designations of this alarm system, it can be noted that the Tomahawk 9010 series (temperature start) is equipped with a blocking relay.
How to connect?
The connection diagram for the ignition of the Tomahawk 9010 alarm is as follows:
- The interaction of current from the starter is carried out during automatic starting from a contact with six terminals.
- A latching relay is connected to the standard wiring socket.
- To reset the dependence of the mass and the signal contact, it is necessary to disable the blocking.
- If you need autostart, it is undesirable to get the blocking relay from the existing circuit.
Let us denote the manipulations aimed at how to program the key fob. "Tomahawk 9010" - a system in which this can be done as follows:
- The main unit with auto start capability is connected via the main socket terminal.
- The power input connector is equipped with ST 1/2 wires.
- This schematic feature is relevant for new domestic cars and foreign cars after the 90th year of production.
Main functionality
When you turn on each mode, a beep sounds. This option allows the vehicle owner to verify that the selected function is correct. When the protective block is activated, the alarm is responded by a short-term siren and flashing lights. If the option is connected correctly, the light sensor will start flashing. The system responds to the execution of the reverse procedure by issuing identical signals.
The kit switches to the immobilizer mode automatically, thirty seconds after the ignition is turned off. The corresponding indicator lights up to confirm the selected option. To turn off this mode, you need to press the button with the image of a closed padlock once.
The "Tomahawk 9010" series, which autostart is remotely carried out by means of a button with a key emblem, informs about the beginning of the mode by flashing parking lights three times, and the necessary indicators are displayed on the remote control monitor. After starting the power unit, the pager will signal with a specific melodic sound.
Peculiarities
If the attempt to start the engine was unsuccessful, the display will show a combination of letters SP. The duration of the engine operation depends on the programming time, at the end of which the power plant will stall. The nuances of this procedure and the available time periods for autorun can be found in the section that says how to program the key fob. "Tomahawk 9010" in the kit contains a standard instruction manual.
Defining the Tomahawk Model
How to find out the model and keychain? "Tomahawk 9010" - a system that can be built into a used car, and the instructions, for example, are lost. Also, a similar question sometimes arises if the control panel is out of order or there is a desire to upgrade the car security system. Anti-theft complexes of this manufacturer are distinguished by excellent protective performance. Depending on the modification, the safety unit is equipped with an automatic start function, the average signal reception distance is at least one kilometer.
Identification criteria
First of all, you need to decide what are the main differences between this brand and other security systems. Features - this is a branded keychain. "Tomahawk 9010" is equipped with five buttons and a branded label on the back. Different modifications of the same brand have some differences between themselves. In the absence of information on the remote control, you need to study its distinctive features and shape. Model 9010 is equipped with a key ring of a standard shape, the characteristic emblem of the company is a schematic drawing of an Indian head with a specific plumage. 
The easiest way to find out the alarm model is by studying the instruction manual. "Tomahawk 9010" is completed with it in each set. Nevertheless, there are situations when there is a need to determine the type of alarm only if there is a main unit and a remote control. Proven methods for determining the model of auto security equipment:
- Marking and inscription on the back of the keychain or in the battery under the power element.
- Modification and a series of signaling are displayed on the main unit of the system. To find out this information, it is necessary to dismantle the lower structure of the car dashboard.
- The keychain also differs in shape, antenna and placement of the monitor. "Tomahawk 9010" has a corporate logo.
Varieties
One of the first security systems of this manufacturer was the Tomahawk 9010 car alarm and the TZ variation. These types of security kits are almost identical. In the improved version, the control panel has undergone changes and a new antenna module has appeared. Key fobs of both modifications are compatible with each other and can function interchangeably. One more hallmark is a radio module that updated version equipped with LED lighting.
The connection scheme and software is similar in both versions. Portable complexes of the Tomahawk 9010 family are designed on different elements. Further development product and functionality allowed to increase the response distance between the console and the main module up to 1.2 kilometers. Budget security variations Z1 and TZ 9010 are no less reliable. In the first set, the range is kept at around one kilometer, and the second instance confidently responds up to 1,300 meters.
Advantages
In addition to an acceptable price, the model in question has additional advantages owing to which it is in demand among car owners:
- Gradual deactivation of the protection mode.
- The liquid crystal display with the programmable block.
- Turbo timer option.
- Variation of "Tomahawk 9010", autostart on which allows you to turn on the engine at a distance.
Tomahawk tz 9010 is a high-tech security device for cars. The tomahawk tz 9010 car alarm is characterized by a huge number of functions, which provides the highest quality car protection.
This alarm is used to protect the car. When choosing security devices, it is necessary to give preference to trusted manufacturers. One of these is the tomahawk alarm.
Equipment Features
The user will learn about a hacking attempt in a timely manner thanks to the integrated shock and tilt sensor. The operation of the equipment is aimed at servicing 16 independent security zones, which ensures high level car safety after installation.
The equipment is characterized by the presence of an individual dialogue encryption code, which excludes the possibility of it being hacked by intruders. If malfunctions occur, the instruction manual will help to eliminate them.
The sensors of the tz 9010 equipment can be quickly configured using a mobile phone. When alarms equipment sends notifications to mobile phone in the form of SMS notifications.
Equipment key fobs The car alarm is equipped with two key fobs, which provides a person with a lot of convenience during its use.
Alarm functions
The tz 9010 is equipped with a trigger memory, which makes it convenient to use.
Also, using the key fob indicator, you can find out about the temperature.
Due to the presence of a low battery warning, the user can always ensure the functionality of the key fob. keyrings car alarm equipped with special buttons, which greatly facilitates its management. The device is characterized by:
- Multifunctionality;
- performance;
- Durability.
This equipment is equipped with a mini-USB port, through which software can be updated.
Due to the presence of an integrated interface in the device, the system control zone is expanded. Additional devices can be connected to this equipment.
It supports a variety of digital buses, which allows it to be used to protect a variety of vehicles. The instruction manual will tell you more about this.
Additional functions
The tz 9010 equipment is characterized by the presence of an integrated GSM interface, with the help of which the control zone is expanded.
When alarm events occur, the car alarm sends a signal to the mobile device, which provides the car owner with a lot of convenience while driving.
Also, thanks to this function, the ergonomics of the operation of this equipment is improved. You can read more about this in the equipment manual.
Thanks to the intelligent automatic start, the engine is started from a distance. At the same time, the main parameters of the engine operation, as well as the state of the vehicle, are monitored.
This feature makes the tz 9010 the most flexible system available. With the help of a multifunctional interface, the anti-robbery and anti-theft resistance of the vehicle is increased.
If necessary, with the help of car alarms, you can control additional devices. How to do this, the instruction manual will tell.
The alarm system is a highly functional security complex, which is characterized by ease of use.
Instruction
Your engine can die at any moment
- Do you think nothing can happen to the engine on a small run?
- If the car began to "eat" oil, then the engine had only a few kilometers left to live.
- 98th gasoline will not save you from an early repair!
To prevent their “iron horse” from being stolen, most motorists have long used numerous alarm systems for this purpose.
Car alarm Tomahawk TZ-9010 is a highly effective anti-theft tool with high reliability, average service life and affordable price.
How to start and turn off the car from the key fob (from the main and additional)
Basic actions available using auto Tomahawk alarms TZ-9010:
- remote start of the car engine by programming the activation functions for a certain time. This is especially important in winter time years, when before the trip it is necessary to warm up the car in advance;
- start of self-diagnostics of systems;
- making a call to the owner of the machine in case of system sensors triggering.
To remotely start the car engine from the Tomahawk TZ-9010 key fob, you must press button 2 (see figure).
Numbering and location of buttons on the Tomahawk TZ-9010 key fob
The success of this action is confirmed by:
- the headlights of the car should blink three times;
- the siren should “respond” three times with a sound alert;
- on the key fob display there will be a corresponding identification about starting / not starting the engine.
After the car engine starts, it can work out the time interval programmed by the system, then automatically turn off.
The engine running time can be extended by five minutes by simultaneously pressing keys “1” and “2”.
To start the car engine remotely, the following conditions must be met:
- switched off ignition;
- the hood is closed;
- Gearbox in neutral;
- the car is on the handbrake.
If these conditions are not met, the machine will “respond” to an attempt to start the engine with a four-time sound alert.
To turn off the car from the key fob (switch off the engine from the key fob) using the Tomahawk TZ-9010, you must press the “2” button, while the car will respond with a double beep and flash the headlights twice.
Starting / stopping the engine of a vehicle from an additional key fob is carried out in the same way as from the main one.
Auto start by temperature, time from key fob
The manufacturer of the TZ-9010 tomahawk has provided in the system a special sensor (engine temperature sensor) mounted under the hood of the vehicle, which is used to provide automatic start by temperature. Which buttons to press: given function is activated by simultaneously pressing buttons “2” and “3” of the key fob.
When the function is activated, an audible signal will sound and the headlights will flash once, while the corresponding indication will appear on the display and the temperature of the automatic activation will be shown. This mode is deactivated (autorun is disabled) by pressing the same buttons again. The reaction of the car will be identical to that when the automation is turned on.
The Tomahawk TZ-9010 system also provides for scheduled start of the car engine. To do this, simultaneously press buttons “2” and “4” on the key fob. If you have completed this action successfully, the car should beep and flash the headlights once. At the same time, the corresponding icon with a clock will be displayed on the key fob and the melody will play.
After activating this function, the vehicle will start at the same time every day.
Scheduled engine start is disabled by pressing the same buttons again.
Additionally, there is a function of monitoring the temperature in the car interior and the state of protection. The request is made by pressing button “3”. To open the trunk, it is necessary to hold the button “3” for a long time.
Why autorun might not work
Among the most common malfunctions of the Tomahawk TZ-9010 alarm are the following:
- “dead” battery in the key fob (the battery is dead). should be replaced;
- the influence of electromagnetic interference on the car (it happens near high-voltage power lines or power plants);
- “lost” the setting of the control panel. In this case, it should be rebooted, possibly even reprogrammed.
If autostart does not work, it is necessary to double-check the connection of all sensors to the vehicle systems.
Your engine can die at any moment
- Do you think nothing can happen to the engine on a small run?
- If the car began to "eat" oil, then the engine had only a few kilometers left to live.
- 98th gasoline will not save you from an early repair!
