Knots for connecting two cables. Herbal Node Ascending Lunar Node in Libra

A surgical knot is a modification of a simple knot. Designed for tying all types of fishing lines together, and will also answer the question how to tie two ends of fishing line. The knot is simple and holds the load well, including when using synthetic lines of different diameters.

It got its name because of its widespread use in medicine for suturing wounds. When tying such a knot, it is necessary to monitor the direction of the cuts - they should be mirrored: first in one direction, then in the other direction.

If this rule is not followed, then when knitting you will get a less reliable improved woman's knot. Depending on the number of turns, it is called a double or triple surgical knot.

The sequence of tying a surgical knot on the two ends of the fishing line:

1. Fold the tied ends of the lines parallel.
2. Fold the running ends of the fishing lines into closed loops.
3. Make 2-3 complete runs around the root ends of the lines with the running ends in the direction of the closed end of the loop.
4. Moisten the lines and tighten the knot.

Herbal knot

The grass knot is used to tie two ends of fishing lines of the same diameter. The positive features of this knot, for tying two ends of fishing lines , refers to the ease of knitting and the fact that it holds the load well and can also be easily unraveled. grass knot is shown in pictures a and b and is described in detail in the instructions below.

The grass knot is most suitable for tying on natural scaffolding or cords; on synthetic scaffolding it slips, so it is advisable to secure it with stopper knots. There are two ways to tie a knot.

Sequence of tying a grass knot

Option 1

1. Place the running ends of the lines parallel to each other.
2. Make a turn with the running ends around the root ends of the opposite lines and pass over the root ends.
3. Tighten the knot.

Option 2

1. Fold one of the lines into a closed loop, passing the running end under the root end.
2. Insert the running end of the second line from above into the loop of the first and, passing under the first running end, throw it over the root end.
3. Pass the second running end under the first loop and over the second running end.
4. Tighten the knot.

These methods of tying fishing lines are taken from an open source literary source.

How to tie two ends of fishing line video

Fishing knot how to tie two ends of fishing line video between each other:

Oak knot. This knot sailors use it in exceptional cases when there is a need to very quickly tie two cables together. It has a serious drawback: a tightly tightened knot is very difficult to untie later, especially if it gets wet. In addition, a cable tied in such a knot has less strength and during operation creates a danger of catching on something during its movement. Its only positive qualities are the speed with which it can be tied. To connect two cables, their ends need to be folded lengthwise together and, stepping back 15-20 centimeters from the edges, tie both ends as one whole with a simple knot. Do not try to tie synthetic cables and fishing line with this knot: it crawls on them. (Fig. 20)

Flemish knot. This is one of the oldest maritime knots, which was used on ships to connect two cables, both thin and thick. There are two ways to knit this node. First, make a figure eight at the end of one of the cables tied together. Towards the exit of the running end, insert the running end of the second cable and repeat figure 8, tied on the first cable. After this, grab each two ends, left and right, and begin to tighten the knot evenly, trying to maintain its shape. For final tightening node pull the root ends of the cables. To connect two cables with a Flemish knot using the second method, place the running ends of the cables being connected parallel to each other so that they touch each other approximately along the length of one meter. At this point, tie a figure eight with two cables folded together. In this case, you will have to carry it around and thread it into the loop along with the short running end of one of the cables and the long main one. This is precisely the inconvenience of the second method of tying the Flemish knot. The connection of two cables with a Flemish knot is considered very strong. This node, even when tightly tightened, does not damage the cable, and it is relatively easy to untie. In addition, it has excellent quality - it is non-slip and holds securely on synthetic fishing line. (Fig. 21)

Water node. The connection of two cables with a water knot is considered no less strong. To tie it, place the ropes to be tied with their ends facing each other so that their ends run parallel and touch each other. Holding the running and root ends of two different cables in one hand, begin to knit an oak knot with them, but instead of one run-out of the root end, make two. Before finally tightening the knot, make sure that one pair of ends comes out of the loop from the top, and the second from the bottom, as shown in the diagram. Water node simple and reliable. (Fig.22)

Babi knot. This knot should not be tied sailors- he is very primitive. A naval man who unluckily tied a woman's knot even on shore will certainly be ridiculed by his colleagues. But among land people this knot is a universal one. However this node traitor. Throughout the history of mankind, he has caused a lot of troubles and even claimed many human lives. The Babi knot consists of two half-knots tied sequentially one above the other in the same direction. If you tie two ropes with it and pull it, you can immediately see that it begins to move along the rope and slide along it. And if it is tied close to one of the tied ends of the rope, then when pulled, it can slip and will certainly slip if the tied ropes are of different thicknesses. Unfortunately, not everyone knows about this and continues to use it. Among the Slavs, this knot got its name due to the fact that from time immemorial women tied the ends of their headscarves with them. When tugging at the main part of the mooring line, the woman's knot turns into a simple bayonet. (Fig. 23)

"Mother-in-law" knot. This knot looks like a woman’s knot and is also not entirely reliable. If the latter has running ends coming out of the knot on one side, then the mother-in-law node they come out from different sides diagonally. (Fig. 24)

Straight knot. It consists of two half-knots, sequentially tied one on top of the other in different directions. There are several ways to knit this sea node. (Fig. 25)

Thief's Knot. It is not recommended to use this knot, since it is completely reliable for tying two cables. There is an interesting version of the origin of the name: to prove the act of stealing from a bag, the owner deliberately tied it with a similar straight knot, and the thief, not paying attention to the catch, tied the robbed bag with a straight knot. (Fig. 26)

Surgical knot. It is used by surgeons for tying ligature threads to stop bleeding and for stitching tissue and skin. When tying a surgical knot, first make two half-knots one after the other with two ends, which are then pulled in different directions. Then another half-knot is tied on top, but in the other direction. The result is a knot very similar to a straight one. The principle of the knot is that the first two half-knots prevent the two ends from moving apart while another half-knot is knitted on top. This knot is convenient to use when there is a need to tighten and tie some kind of burden with a rope. (Fig. 27)

Academic node. It is very similar to a surgical knot, the only difference being that instead of one half-knot it has two. This has the advantage that when there is a large load on the cable, it is not tightened as much as a straight knot, and it is easier to untie it in the usual way. (Figure 28)

Flat knot. It has long been considered one of the most reliable knots for tying cables of different thicknesses. They even tied anchor hemp ropes and moorings. After removing the load on the cable, this knot is easy to untie. The principle of a flat knot lies in its shape: it is really flat, and this makes it possible to select the cables connected to it on the drums of capstans and windlasses. In maritime practice, there are two options for tying this knot: a loose knot with its free running ends tacked to the main or half-bayonets at their ends (a) and without such a tack when the knot is tightened (b). This knot indispensable for tying two cables (even steel ones, on which significant force will be applied, for example, when towing a heavy truck). (Fig. 29)

Dagger knot. In foreign rigging practice, this knot is considered one of the best knots for connecting two large diameter cables. It is not very complex in its design and is quite compact when tightened. It is most convenient to tie it if you first lay the running end of the cable in the form of a figure 8 on top of the main one. After this, pull out the running end of the second cable and thread it through the loops, pass it under the middle intersection of the figure eight and bring it above the second intersection of the first cable. Next, the running end of the second cable must be passed under the root end of the first cable and inserted into the figure eight loop, as the arrow indicates. When the knot is tightened, the two running ends of both cables stick out in different directions. The dagger knot is easy to untie if you loosen one of the outer loops. (Fig. 30)

Herbal knot. It comes undone easily in the absence of traction. Used for tying two belts or two ribbons. For this purpose, the “grass” knot is very convenient (Fig. 31).

Packet node. Its name speaks about its application. Simple, original and designed for quick knitting. In terms of strength, it is not inferior to a grass knot. (Fig. 32)

Fisherman's knot. It is a combination of two simple knots tied with the running ends around the alien root ends. To tie two cables with a fisherman's knot, you need to put them towards each other and make a simple knot with one end, and pass the other end through its loop and around the root end of the other cable and also tie a simple one node. Then you need to move both loops towards each other so that they come together and tighten the knot. The fisherman's knot, despite its simplicity, can be safely used to tie two cables of approximately the same thickness. Used for tying fishing line (not synthetic) and for attaching leashes to fishing line. (Fig. 33)

Snake knot. This node is considered one of the most reliable nodes for tying synthetic fishing gear. It has quite a lot of weave, is symmetrical and relatively compact when tightened. With a certain skill, you can even tie the strings of a piano with it. The snake knot can be successfully used to tie two cables made of any materials when a strong, reliable connection is required. (Fig. 34)

weaving knot. Some weaving knots have long been borrowed by sailors in their original form and serve them reliably. The weaving knot can be called the “brother” of the clew knot. The only difference is in the method of tying it and in the fact that the latter is tied into a krengel or into a sail, while the weaving knot is knitted with two cables. (Fig. 35)

Versatile knot. This knot is similar to a weaving knot in its principle. The only difference is that when tied, the running ends point in different directions - this is very important when tying. This knot is famous for the fact that it can be tied at its base " king of knots" - gazebo knot. (Fig. 36)

Clew knot. It got its name from the word “sheet” - a tackle that is used to control the sail, stretching it by one lower corner if it is oblique, and at the same time by two if it is straight and suspended from the yard. The sheets are named after the sail to which they are attached. IN sailing fleet This knot is used when there is a need to tie the tackle into the fire of the sail. The clew knot is simple and very easy to untie, but it fully justifies its purpose - it securely holds the clew in the sail's crest. (Fig. 38)

Windlass knot. This nautical knot is used to tie topsheets and boom-sheets, top-halyards and boom-bram-halyards, as well as top-sheets. The clew knot is more reliable than the clew knot because it does not immediately untie when the pull on the cable stops. It differs from the previous sea knot in that the loop (or krengel) is surrounded by the running end not once, but twice, and passed under the root end twice. During times sailing fleet The windlass knot was widely used when working with gear. It was used when it was necessary to take the tackle to the fire. (Fig. 39)

Docker node. In maritime practice, it often becomes necessary to attach a much thinner cable to a thick rope. There is always such a need when a ship is moored to a pier, when one or several mooring lines need to be supplied from the deck. To tie this knot, fold the running end of the thick cable, to which the thin cable must be attached, in half. Insert a thin cable into the resulting loop from below, make one run around the root part of the thick cable, pass it under the thin cable, then over the running end of the thick cable, and then under the three cables, insert it into the loop. This nautical node reliable enough to use the throwing end to pull out a heavy mooring line. (Fig. 40)

Furrier's knot. It is relatively simple, has many crossed ends and is quite compact. In addition, the furrier's knot has an excellent property: designed for strong traction, it is tightly tightened and untied without much difficulty. This knot can be successfully used for tying synthetic cables and fishing lines. (Fig. 41)

Liana knot. This node has not been distributed to navy, but is one of the original and reliable knots for tying cables. With a very simple interweaving of each end separately, it holds tightly under very strong traction and, moreover, very easily unties after removing the load on the cable. It does not slip on synthetic fishing line and can be successfully used by anglers. (Fig. 42)

Hunting knot. In our time, inventing a new knot is not an easy task, since over five thousand years more than 500 of them have been invented. Therefore, it is no coincidence that the invention of a new knot by the English doctor Edward Hunter in 1979 caused a sensation in maritime circles. Essentially, a hunting knot is a successful interweaving of two simple knots tied at the ends of the cables. It holds perfectly on all lines, including the thinnest synthetic lines. Since Hunter means “hunter” in English, the knot was called a hunting knot. (Fig. 43)

Afrikaans Albanian Arabic Armenian Azerbaijani Basque Belarusian Bulgarian Catalan Chinese (Simplified) Chinese (Traditional) Croatian Czech Danish Detect language Dutch English Estonian Filipino Finnish French Galician Georgian German Greek Haitian Creole Hebrew Hindi Hungarian Icelandic Indonesian Irish Italian Japanese Korean Latin Latvian Lithuanian Macedonian Malay Maltese Norwegian Persian Polish Portuguese Romanian Russian Serbian Slovak Slovenian Spanish Swahili Swedish Thai Turkish Ukrainian Urdu Vietnamese Welsh Yiddish ⇄ Afrikaans Albanian Arabic Armenian Azerbaijani Basque Belarusian Bulgarian Catalan Chinese (Simplified) Chinese (Traditional) Croatian Czech Danish Dutch English Estonian Filipino Finnish French Galician Georgian German Greek Haitian Creole Hebrew Hindi Hungarian Icelandic Indonesian Irish Italian Japanese Korean Latin Latvian Lithuanian Macedonian Malay Maltese Norwegian Persian Polish Portuguese Romanian Russian Serbian Slovak Slovenian Spanish Swahili Swedish Thai Turkish Ukrainian Urdu Vietnamese Welsh Yiddish

English (auto-detected) » Russian

Marine site Russia no November 02, 2016 Created: November 02, 2016 Updated: July 09, 2017 Views: 5046

Sailors use it only in exceptional cases, when there is a need to very quickly tie two cables together. Although connecting plant cables with an oak knot is quite reliable, it has a serious drawback: a tightly tightened knot is very difficult to untie later, especially if it gets wet. In addition, a cable tied in such a knot has less strength and during operation creates a danger of catching on something during its movement.

Its only positive qualities are the speed with which it can be tied and its reliability. To connect two cables, their ends need to be folded lengthwise together and, stepping back 15-20 centimeters from the edges, tie both ends as one whole with a simple knot. Do not try to tie synthetic cables and fishing line with this knot: it crawls on them.

Just like the clew knot, it got its name from the name of the gear - the top sheet, which is used to stretch the clew knots of the lower edge of a straight sail when setting the top sails.
If the single sheets of the lower sails are tied with a clew knot, then the top clew and boom halyards, top halyards and boom halyards, as well as top halyards are tied with a top clew knot. The clew knot is more reliable than the clew knot because it does not immediately untie when the pull on the cable stops.

It differs from a clew knot in that the loop (or krengel) is surrounded by the running end not once, but twice, and is also passed under the main end twice. In the days of the sailing fleet, the front clevis knot was widely used when working with gear. It was used when it was necessary to take some kind of gear into the fire, for example, top sheets and top sheets.

Usually they tied the bram-gins in the bram-halle and the gins in the topenant of the lower yards. The windlass knot is also reliable for tying two cables of different thicknesses. It holds well on synthetic cables of equal thickness.

In our time, inventing a new knot is almost incredible, since no more than 500 of them have been invented over five thousand years. Therefore, it is no coincidence that the invention of a new unit by retired English doctor Edward Hunter in 1979 caused a kind of sensation in maritime circles in many countries.

British patent experts, issuing Hayter a patent for his invention, recognized that the unit was indeed new. Moreover, it holds perfectly on all lines, including the thinnest synthetic lines.
Essentially, a hunting knot is a successful interweaving of two simple knots tied at the ends of the cables. Dr. Hunter did not pursue the goal of inventing a new knot, but tied it completely by accident.

Since the surname Hunter means “hunter” in English, we called this knot a hunting knot.

Herbal knot

Despite its name, this elementary unit is quite reliable and can withstand heavy loads. In addition, it can be easily untied in the absence of traction. The principle of the knot is half bayonets with other ends (Fig. 31, a). Sometimes we have to tie two belts or two ribbons, well, let's say, reins. For this purpose, the “grass” knot is very convenient (Fig. 31, b). It can be tied by slightly changing the “mother-in-law’s” knot (see Mother-in-law’s knot) or starting with half bayonets, as shown in the diagram (Fig. 31, a). When you tighten the “grass” knot by the root ends, the knot twists and takes on a different shape. When it is completely tightened, the two running ends point in the same direction.

Sea knots. - M.: Transport. L. M. Skryagin. 1984.

See what a “Grass Knot” is in other dictionaries:

Surprising but true. Some people, when tying two ropes together, somehow manage to tie a so-called “mother-in-law” knot, somewhat reminiscent of a woman’s knot. If the latter has running ends coming out of the knot on one side, then the mother-in-law knot... ... Nautical knots

Its name suggests that it is convenient for tying bags and bundles. It is simple, original and designed for quick knitting. The packet knot is somewhat reminiscent of a grass knot. In terms of strength, it is not inferior to the latter. Rice. 32. Packet knot...Nautical knots

- (see Oak knot) (see Flemish knot) (see Water knot) (see Woman's knot) (see Mother-in-law's knot) (see Straight knot) (see Thief's knot) (see Surgical knot) ( see Academic knot) (see Flat knot) (see Dagger knot) (see Grass knot)… … Nautical knots

FEED SHOP- in the village X. enterprise, is intended for the preparation of wet multicomponent feed mixtures immediately before feeding them to women. K. object of the feeding area; equipment of its in-line technologies. lines are adapted for blocking with unloading... Agricultural Encyclopedic Dictionary

feed shop- A layout diagram of the technological equipment of the KOPK 15 feed shop in standard premises; B diagram (sectional view) of the main feed mixing production line: 1 feeder tray for silage or haylage; 2, 3, 11, 13, 14, 15 … … Agriculture. Large encyclopedic dictionary

Coordinates: 55°42′ N. w. 36°58′ E. d. / 55.7° n. w. 36.966667° E. d. ... Wikipedia

Country Russia Status Municipal district ... Wikipedia

Agriculture is the most important part of the country’s national economic complex, one of the main areas of material production, which has a great influence on improving the well-being of workers and the pace of development of the Soviet economy: products ... Great Soviet Encyclopedia

City, adm. c. Western state Bengal, India. Founded in 1696 on the site of three villages, one of which was called Kalikata, modern. Calcutta. The name comes from Kali, the wife of the Hindu god Shiva, and... i.e. the basics of kata dwelling, i.e. the abode of the goddess... ... Geographical encyclopedia

Union of Myanmar, state in Southeast. Asia. Modern name Myanmar (Myanma) country of the Myan people. Until 1989, the country was called Burma (cf. French Birmanie, English Burma). See also Salween. Geographical names... Geographical encyclopedia

How much irony and disdain can be heard from sailors towards this primitive and, unfortunately, unit that has firmly taken root in our everyday life. This is exactly what sailors should not do - tie this knot. A naval man who unluckily tied a woman's knot even on shore will certainly be ridiculed by his colleagues. Like, this is a disgrace for the fleet. But, alas, among land people this knot is a universal one. The vast majority of people who are not familiar with rigging, or those who, by their profession, do not deal with ropes, ropes, or threads, use the woman’s knot in all cases when they need to tie, tie or tie something . It seems that people, having learned this knot in childhood, believed so strongly in its utilitarian nature that they don’t even want to hear about any other complex sea knots. Nevertheless, speaking seriously, this traitorous knot has caused a lot of troubles throughout the history of mankind and even claimed many human lives. The Babi knot consists of two half-knots tied sequentially one above the other in the same direction. If you tie two ropes with it and pull it, you can immediately see that it begins to move along the rope and slide along it. And if it is tied close to one of the tied ends of the rope, then when pulled, it can slip and will certainly slip if the tied ropes are of different thicknesses. Unfortunately, not everyone knows about this and continues to use it. In our country, this knot got its name due to the fact that from time immemorial women tied the ends of their headscarves with it. Abroad, it is called the “grandmother’s”, “stupid”, “veal”, “false”, “newborn” knot. But, oddly enough, sailors and fishermen of some countries use the woman’s knot in their work. In addition to its negative qualities (sliding and not being untied), they caught one of its positive properties - under certain conditions, it can instantly turn into a simple bayonet - into one of the simplest and most reliable sea knots for securing the mooring of a vessel on the shore with a pole, bollard or mooring bollard . But in order to tie a simple bayonet when mooring, you need to get off the ship ashore and do it directly at the fireplace or bring the end to the shore so that those standing on the shore can do it. But it turns out that a simple bayonet can be tied to the mooring bollard without leaving the ship ashore. And this is done with the help of a woman’s knot, despised by sailors... To do this, at the end of the cable, which they intend to bring ashore for fastening it with a simple bayonet around the pole, a loop is made, the running end of which is connected to the root end with a woman’s knot, which is not fully tightened. From the side of the ship this loop is thrown onto the pole. When tugging at the main part of the mooring line, the woman's knot turns into a simple bayonet.